   KPG-67D Help File Version 1.00 1'st Release.
                             1.02
                             1.10 G 5-Tone, KPG-67D(V2.10) Ver.UP.
                             1.11 Change some setting item name, KPG-67D(V2.11)

   File name: KPG67D_1.HLP


General Help
General Help

***[SOFTWARE LICENSE NOTICE]***

1  The copyright for the software is owned by KENWOOD Corporation.
2  The software must not be used nor copied except as authorized in
   writing by KENWOOD Corporation.
3  KENWOOD Corporation accepts no responsibility for the effects
   caused by the use of the software.
4  The specifications of the software are subject to change without
   notice.
5  The software has been carefully designed; however, after reviewing
   the given descriptions, if you have questions, encounter mistakes,
   or discover absence of necessary information, please contact
   KENWOOD Corporation.

IBM is a trademark registered by International Business Machines
Corporation.


***[HANDLING OF FLOPPY DISKS]***

Observe the following points when handling the provided floppy disks:

* Never touch the magnetic surface of the floppy disks.
* Keep magnets and magnetic objects away from the floppy disks.
* Do not bend the floppy disks.
* Do not place the floppy disks in dusty, wet, humid, dry, hot, nor
  cold areas.
* Always insert the floppy disks back into the plastic cases after
  use.


1  INTRODUCTION
================

KPG-67D software is a tool for programming TK-760G/762G/860G/862G/260G
/270G/360G/370G transceivers.
Using this software, first enter programming data into the appropriate
computer, then transfer the data to a transceiver.  You can print out
that data from a printer.  You can also retrieve data from a
transceiver to edit on the computer.


***[SUPPLIED ITEMS]***

Your programming software package includes the followings:

* 2 floppy disks (3.5", 1.44 MB)
    KPG-67D PROGRAMMING DISK (program files)
    KPG-67D MANUAL DISK (help files)
* Installation sheet


***[APPLICABLE TRANSCEIVERS]***

This programming software supports the following transceivers:

TK-760G (Mobile;VHF)
TK-762G (Mobile;VHF)
TK-860G (Mobile;UHF)
TK-862G (Mobile;UHF)
TK-260G (Portable;VHF)
TK-270G (Portable;VHF)
TK-360G (Portable;UHF)
TK-370G (Portable;UHF)


***[HARDWARE/ SOFTWARE REQUIREMENTS]***

< Computer >

The software was designed for use on IBM PC, AT, PS/2 and compatible
computers with Conventional Memory capacity of at least 530 kB.

< Operating system (OS) >

The operating system must be IBM DOS Version 3.1 (or later) or
equivalent.

< Communication port >

The computer must have a serial communication port to connect with a
transceiver.  This port must be compatible with an IBM asynchronous
communications adapter. You may use the COM1 or COM2 port on the
computer.

< Connection cable >

Use a KPG-22(for portable) or a KPG-46(for mobile) cable to connect
the computer with the transceiver.



2  CONNECTING THE EQUIPMENT
=============================

1. Switch OFF the power to the computer.
2. Connect the 25-pin connector on the KPG-22/46 cable to the COM1 or
   COM2 port on the computer.  If the COM port has 9 pins, use a
   commercially available 9-pin/25-pin adapter.
3. Switch ON the power to the computer.
4. Switch OFF the power to the transceiver.
5. Connect the other end of the KPG-22/46 cable to the universal
   connector on the transceiver.
6. Switch ON the power to the transceiver.


3   INSTALLING THE SOFTWARE
=============================

After completing all physical connections, you are ready to install
the programming software. 
The KPG-67D software requires a destination drive with 1300kB free
space.

***[INSTALLING ON A HARD DISK]***

This procedure assumes the hard disk is drive C.

1. Insert the "KPG-67D PROGRAMMING DISK" (source disk) into drive A.
2. Type "A:" then press [Enter].
   "A:\>" appears on the computer display.
3. Type "INSTALL C:" then press [Enter].
   The installation program copies the necessary files from the
   source disk in drive A to the hard disk.


***[INSTALLING ON ANOTHER FLOPPY DISK]***

This procedure assumes the source drive is A, and the destination
drive is B.

1. Insert the "KPG-67D PROGRAMMING DISK" (source disk) into drive A.
2. Insert a floppy disk (destination disk), that will receive the
   software, into drive B.
3. Type "A:" then press [Enter].
   "A:\>" appears on the computer display.
4. Type "INSTALL B:" then press [Enter].
   The installation program copies the necessary files from the source
   disk in drive A to the destination disk in drive B.


4  PROGRAM OVERVIEW
====================

***[SYSTEM FLOW CHART]***

This chart provides an overview of all functions offered in the menus
of the programming software.

 +-- CHANNEL
 |    INFORMATION --+- Receive Frequency
 |                  +- Transmit Frequency
 |                  +- QT/DQT Decode
 |                  +- QT/DQT Encode
 |                  +- Channel Name
 |                  +- TX Power
 |                  +- Wide/Narrow
 |                  +- Scan Delete/Add
 |                  +- Option Signalling
 |
 +-- GROUP EDIT ----+- Group Name
 |                  +- Group Delete/Add
 |
 +-- CHANNEL EDIT --+- Receive Frequency
 |                  +- Transmit Frequency
 |                  +- QT/DQT Decode
 |                  +- QT/DQT Encode
 |                  +- Channel Name
 |                  +- Option Signalling
 |                  +- ID
 |                  +- Busy Channel Lockout
 |                  +- Beat Shift
 |                  +- TX Power
 |                  +- Wide/Narrow
 |                  +- Scan Delete/Add
 |                  +- Priority Channel
 |                  +- Home Channel
 |                  +- Compander
 |                  +- PTT ID
 |                  +- Begin of TX
 |                  +- End of TX
 |                  +- Dec 1
 |                  +- Dec 2
 |                  +- Call 1
 |                  +- Call 2
 |                  +- Trsp
 |                  +- PTT ID Mon.
 |                  +- Call 1 Mon.
 |                  +- Call 2 Mon.
 |
 +-- FILE -----+- New
 |             +- Load
 |             +- Save  (=F4)
 |             +- Save As
 |             +- Delete
 |             +- Print (=F5)
 |             +- Go to DOS
 |             +- Exit  (=F3)
 |
 +-- MODEL ----+- Mobile   -+- TK-762G[VHF:8CH]E
 |             |            |
 |             |            +- TK-762G[VHF:8CH](N)E
 |             |            |
 |             |            +- TK-760G[VHF:128CH]E
 |             |            |
 |             |            +- TK-760G[VHF:128CH](N)E
 |             |            |
 |             |            +- TK-862G[UHF:8CH]E
 |             |            |
 |             |            +- TK-862G[UHF:8CH](N)E
 |             |            |
 |             |            +- TK-860G[UHF:128CH]E
 |             |            |
 |             |            +- TK-860G[UHF:128CH](N)E
 |             |            
 |             |
 |             +- Portable -+- TK-260G[VHF:8CH]E
 |                          |
 |                          +- TK-260G[VHF:8CH](N)E,(N)T
 |                          |
 |                          +- TK-270G[VHF:128CH]E
 |                          |
 |                          +- TK-270G[VHF:128CH](N)E,(N)T
 |                          |
 |                          +- TK-360G[UHF:8CH]E
 |                          |
 |                          +- TK-360G[UHF:8CH](N)E
 |                          |
 |                          +- TK-370G[UHF:128CH]E
 |                          |
 |                          +- TK-370G[UHF:128CH](N)E
 |
 +-- EDIT -----+- Optional Features 
 |             |           -+- Group Name Text Size
 |             |            +- Number of Trunking Groups
 |             |            +- Power On Tone
 |             |            +- Control Tone
 |             |            +- Warning Tone
 |             |            +- Busy Channel Lockout Tone
 |             |            +- Minimum Volume(Mobile)
 |             |            +- Tone Volume(Mobile)
 |             |            +- Number of Passes
 |             |            +- Display Character
 |             |            +- On Hook Reset (5-Tone) (Mobile)
 |             |            +- Off Hook Decode (QT/DQT) (Mobile)
 |             |            +- Off Hook Horn Alert(Mobile)
 |             |            +- Startup Horn Alert(Mobile)
 |             |            +- Horn Alert Time(Mobile)
 |             |            +- Speaker Muting by Off Hook(Mobile)
 |             |            +- Data TX with QT/DQT(Mobile)
 |             |            +- Key Lock
 |             |            +- Power On Text
 |             |            +- Acc Hook/DTC(Mobile)
 |             |            +- Time Out Timer(TOT)
 |             |            +- TOT Pre-Alert
 |             |            +- TOT Rekey Time
 |             |            +- TOT Reset Time
 |             |            +- Clear to Transpond
 |             |            +- Transpond Delay
 |             |            +- Battery Save(Portable)
 |             |            +- Signalling
 |             |            +- SQ Level
 |             |            +- Auto Lamp(Portable)
 |             |            +- Radio Password
 |             |            +- Data Password
 |             |            |
 |             |            +- Mode ------+- Panel Test
 |             |            |             +- Panel Tuning
 |             |            |             +- Firmware Programming
 |             |            |             +- Clone
 |             |            |             +- Self Programming
 |             |            |
 |             |            +- Emergency -+- Emergency Code
 |             |              (Mobile)    +- Emergency Ack Code
 |             |                          +- Emergency Reset Code
 |             |                          +- Emergency
 |             |                              Mode Recognition
 |             |                          +- Emergency
 |             |                              Ack Recognition
 |             |
 |             +- Key Assignment ----+- SCN Switch
 |             |   (Mobile 128ch)    +- A Switch
 |             |                     +- D/A Switch
 |             |                     +- Monitor Switch
 |             |                     +- CH Up
 |             |                     +- CH Down
 |             |                     +- Volume Up
 |             |                     +- Volume Down
 |             |                     +- Group Up
 |             |                     +- Group Down
 |             |                     +- Foot Switch
 |             |
 |             +- Key Assignment ----+- Monitor Switch
 |             |   (Mobile 8ch)      +- Open Circle Switch
 |             |                     +- Closed Circle Switch
 |             |                     +- A Switch
 |             |                     +- CH Up
 |             |                     +- CH Down
 |             |                     +- Volume Up
 |             |                     +- Volume Down
 |             |                     +- Foot Switch
 |             |
 |             +- Key Assignment ----+- Open Circle Switch
 |             |   (Portable 128ch)  +- Closed Circle Switch
 |             |                     +- < Switch
 |             |                     +- > Switch
 |             |                     +- Side1 Switch
 |             |                     +- Side2 Switch
 |             |                     +- Knob Select
 |             |
 |             +- Key Assignment ----+- Side1 Switch
 |             |   (Portable 8ch)    +- Side2 Switch
 |             |
 |             +- Scan Information --+- Priority
 |             |                     +- Look Back Time A
 |             |                     +- Look Back Time B
 |             |                     +- Revert Channel
 |             |                     +- Dropout Delay Time
 |             |                     +- Dwell Time
 |             |                     +- Group Scan
 |             |                     +- Off Hook Scan(Mobile)
 |             |
 |             +- DTMF --------------+- Digit Time
 |             |                     +- Inter Digit Time
 |             |                     +- First Digit Time
 |             |                     +- First Digit Delay
 |             |                     +- Rise Time with QT
 |             |                     +- Dial ID
 |             |                     +- No. of DTMF Key
 |             |                     +- DTMF Hold Time
 |             |                     +- Keypad Auto-PTT
 |             |                     +- Store & Send
 |             |                     +- D Key Assignment
 |             |                     +- Auto Dial Memory
 |             |                     +- DTMF Signalling
 |             |                     +- Intermediate Code
 |             |                     +- Group Code
 |             |                     +- Auto Reset Timer
 |             |                     +- Call Alert/Transpond
 |             |                     +- Transpond
 |             |                     +- Dead Beat Disable(TX)
 |             |                     +- Dead Beat Disable(TX&RX)
 |             |
 |             +- 5-Tone (1)---------+- 5-Tone-Standard
 |             |                     +- Tone Period
 |             |                     +- Receive Gap Period
 |             |                     +- First Tone Period
 |             |                     +- 'F' No-Tone Period
 |             |                     +- Auto Reset Timer
 |             |                     +- Delay TX On Time
 |             |                     +- Delay TX Off Time
 |             |                     +- 'T' External Single Tone
 |             |                     +- Next Decode Wait
 |             |                     +- KENWOOD Format...
 |             |                     +- Group Tone
 |             |                     +- Group Digit Selectable
 |             |                     +- LED Condition (Signalling)
 |             |                     +- Selectable Selcall Digit
 |             |                     +- Monitor Function
 |             |                     +- Start Up Monitor
 |             |                     +- Mute Monitor Tone
 |             |                     +- Min. Mute Tone Period
 |             |                     +- Enc/Dec Code...
 |             |                     +- 5-Tone (2) menu...
 |             |
 |             +- 5-Tone (2)---------+- PTT ID Control
 |             |                     +- Number of Start Up ID
 |             |                     +- My ID Text
 |             |                     +- Keypad Text
 |             |                     +- Queue Text
 |             |
 |             +- 2-Tone ------------+- A Tone
 |             |                     +- B Tone
 |             |                     +- C Tone
 |             |                     +- Decoder Call Format
 |             |                     +- Group Call
 |             |                     +- Alert Tone/Transpond
 |             |                     +- Auto Reset Timer
 |             |                     +- 2-Tone Encode
 |             |
 |             +- Test Frequency------- No.1-No.16 RX/TX Frequency
 |             |
 |             +- Embedded Message (64 characters max.)
 |             |
 +-- PROGRAM --+- Read from Radio
 |             +- Write to Radio
 |             +- Test Mode --------+- Frequency Channel
 |             |                    +- Signalling Tone
 |             |                    +- Wide/Narrow
 |             |                    +- Battery Warning Level
 |             |                    |  (Portable)
 |             |                    +- Frequency Adjustment (Mobile)
 |             |                    +- RF High Power
 |             |                    +- RF Low Power
 |             |                    +- QT VCO Balance (Portable)
 |             |                    +- QT TCXO Balance (Portable)
 |             |                    +- DQT VCO Balance (Portable)
 |             |                    +- DQT TCXO Balance (Portable)
 |             |                    +- Max Deviation
 |             |                    +- DQT Balance (Mobile)
 |             |                    +- QT Fine Deviation
 |             |                    +- DQT Fine Deviation
 |             |                    +- DTMF Fine Deviation
 |             |                    +- Single Tone Fine Deviation
 |             |                    +- Sensitivity
 |             |                    +- Squelch(Tight)
 |             |                    +- Squelch(Open)
 |             |                    +- Print Tuning Data
 |             |
 |             +- Firmware Program
 |             +- Check sum
 |             +- ESN
 |
 +-- SETUP ----+- Communication Port
 |             +- Display Color ----+- Color ---+- Display Back Color
 |             |                    |           +- Input Data Color
 |             |                    |           +- Feature Highlight
 |             |                    |           |    Color
 |             |                    |           +- Screen Border
 |             |                    |           |    Information Color
 |             |                    |           +- Window Menu Color
 |             |                    |           +- General Message
 |             |                    |           |    Color
 |             |                    |           +- Windows Color
 |             |                    |           +- Help Window Color
 |             |                    |
 |             |                    +-Black & White
 |             |
 |             +- Help Path
 |             +- Fpro Path
 |
 +-- HELP -----+- General Help
               +- Keyboard Help (Computer Keyboard)


***[PROGRAMMING METHODOLOGY]***

This section shows the logical process of three typical programming
operations.

Note:  When data is transferred from the computer to the transceiver
       (Program Write) or vice versa (Program Read), the transceiver
       will automatically enter PC mode.  "-PC-" appears on the
       display.


**[CREATING AND WRITING NEW DATA TO A TRANSCEIVER]**

1. Specify the transceiver model. (Model)
2. Input data. (Edit)
3. Write the data to the transceiver. (Program/Write to radio)
4. Save the data to a disk. (File/save As)


**[MODIFYING DATA PREVIOUSLY WRITTEN TO A TRANSCEIVER]**

1. Read the desired data from the transceiver. 
   (Program/Read from radio)
2. Modify the data. (Edit)
3. Write the data to the transceiver. (Program/Write to radio)
4. Save the data to a disk. (File/save As)


**[MODIFYING DISK DATA, THEN WRITING TO A TRANSCEIVER]**

1. Read the desired data from a disk. (File/Load)
2. Modify the data. (Edit)
3. Write the data to the transceiver. (Program/Write to radio)
4. Save the data to a disk. (File/save As)


5  BASIC OPERATIONS
====================

***[STARTING THE PROGRAM]***

After correctly installing the software, you can now start the
program and learn the methods for programming TK-760G/762G/860G/862G/
260G/270G/360G/370G transceivers.

1. Make the directory containing the installed programming software
   the current directory.
   If you installed the software on a floppy disk, first insert the
   floppy disk into a drive, then make that drive the current drive.
2. Type "KPG67D" then press [Enter].
   The program starts and the Introductory screen appears.  If an
   error occurs, try reinstalling the program (see "3  INSTALLING THE
   SOFTWARE").


***[EXITING THE PROGRAM]***

When you finished programming, close the program correctly rather
than simply turning off the computer.

1. Press [Alt] to activate the Menu bar.
2. Press the right- or left-arrow key to open the File menu.
   Move the cursor to "eXit" using the up- or down-arrow key, then
   press [Enter], or simply press the Quick key; the capitalized
   letter in this case "X".  Pressing [F3] also opens this window.
4. Select [Ok] using [SPACE BAR], or the right- or left-arrow key,
   then press [Enter].  Alternatively, press the Quick key "O" if you
   prefer. The program closes and the DOS prompt appears.
5. If running the program from a floppy disk, remove the disk from its
   drive.
6. Switch OFF the power to the computer.
7. Switch OFF the power to the transceiver.


***[INITIAL SCREEN]***

After starting the program, pressing any key clears the Introductory
screen and opens the Initial screen.

The Initial screen consists of the following three sections:

* Menu bar (top)
* Channel Information window (center)
* Key summary (bottom)

< Menu bar >

The Menu bar contains the titles of available menus.  The menus are
used to open windows to edit and/or process data, and to execute
commands.

< Channel Information window >

The Channel Information window shows various Channel data currently
set.

< Key summary >

The Key summary lists currently available keys.


***[SELECTING AND ENTERING DATA]***

You will select or enter data either while an interactive window is
visible (prompted input) or while no interactive window is visible
(non-prompted input).


**[PROMPTED INPUT]**

While using File, Model, Program, Setup, or some Edit menu functions,
various interactive windows open to prompt you to select or enter
appropriate data.  Use one of the following methods:

< Arrow keys >

Use the right-, left-, up-, or down-arrow key to select the
appropriate item, then press [Enter].

< Quick keys >

Enter the capitalized letter to select the appropriate item.  For
example, press "O" to select "[Ok]".  If you are using a color
display, capitalized letters appear in a different color from other
characters.

< Keyboard >

Enter the appropriate data using the keyboard, then press [Enter].


**[NON-PROMPTED INPUT]**

When using some Edit menu functions, use one of the following methods
to select data.

< [SPACE BAR]/ [Shift]+ [SPACE BAR] >

Press to cycle through available choices at the current cursor
position. Pressing [SPACE BAR] changes selections in one direction;
pressing [SHIFT]+[SPACE BAR] changes selections in the opposite
direction.

< [F2]/ [Shift]+ [F2] >

Press to cycle through available choices at the current cursor
position. Pressing [F2] changes selections in one direction; pressing
[Shift]+ [F2] changes selections in the opposite direction. In the
Key assignment window, pressing [F2] opens a list of programmable key
functions.


6  USING THE MENU
==================

***[MENU OVERVIEW]***

The Menu bar is at the top of the Initial screen, above the Channel
Information window.  There are six menu titles on the Menu bar.  To
activate the Menu bar, press [Alt].  Use the right- or left-arrow key
to select the desired menu title.  Press [Alt] or [Esc] to deactivate
the Menu bar.

< File >
The File menu allows you to create, save, open, delete, and print data
files, and to quit the program.

< Model >
The Model menu is used to specify the model of the transceiver to be
programmed.

< Edit >
The Edit menu allows you to assign various functions to the desired
keys on the transceiver, and to configure transceiver functions that
are not programmed from the Channel Information window.

< Program >
The Program menu allows you to read data from and write data to flash
memory or EEPROM in the transceiver.  The Program menu allows you to
read data from and write data to EEPROM in the trunking board. This 
menu also allows you to access the Test mode or Firmware program.

< Setup >
The Setup menu allows you to select a communication port on the
computer to connect with the transceiver via the KPG-22/46 cable.
Other configurable items include the color scheme for the screen as
well as the drive and path name for access to the Help file.

< F1=Help >
The Help menu offers general and keyboard help.


***[MENU DETAILS]***

This section describes the menu items selectable under the menu titles
and shows how to operate these menu items.  Use the Up- or Down-arrow
key to select the desired menu item, then press [Enter], or simply use
a quick key.
For the methods of selecting or entering data for each menu item, see
"***[SELECTING AND ENTERING DATA]***" in chapter 5.


**[FILE]** 

< New >

This function clears all data currently shown in the channel
information window and restores the defaults.

1. Select "New" then press  [Enter], or simply press [N]. A warning
   message appears.
2. Select "[Ok]" or "[Cancel]". Then press [Enter], or simply press 
   [O] or [C].

< Load >

The Load function reads a data file saved on a hard disk or floppy
disk, then writes the file into the buffer memory of your computer.
You may change the loaded file, write it to the transceiver, or print
it out.

1. Select "Load" then press [Enter], or simply press [L]. The "Drive
   & Path" window opens, and displays the currently selected drive
   and path name.
2. Type the drive and path name of the desired file, then press
   [Enter]. The "Directory" window opens and displays the name(s) of
   the file(s) on that path.  Data files have "DAT" extensions.

   If the entered drive does not contain a disk, an error message
   appears. Press any key, insert the correct disk in the specified
   drive, then press [Enter].

   If the entered drive or path does not exist, an error message
   appears. Press any key, correct the drive or path name, then press
   [Enter].

   If no file is found under the drive and path name, an error message
   appears. Press any key, correct the drive and path names, then
   press [Enter].

3. Select the desired file name, then press [Enter].  The "Load file
   name" window opens.
4. Select "[Ok]" or "[Cancel]" then press [Enter], or simply press
   [O] or [C].

< Save(=F4) >

The Save function saves the created or revised file to the drive,
path, and file names previously selected (or default).

1. Select "Save(=F4)" then press [Enter], or simply press [S] or [F4].
   If the same file name exists under the current path, a warning
   message appears. If the same file name does not exist under the
   current path, the "Save file name" window opens.
2. Select "[Ok]" or "[Cancel]" then press [Enter], or simply press
   [O] or [C].

< save As >

The save As function saves the current file to the drive, path, and
file names that you specify.

1. Select "save As" then press [Enter], or simply press [A]. The
   "Drive & Path" window opens and displays the currently selected
   drive and path names.
2. Type the desired drive and path names, then press [Enter].  The
   "Save file name" window opens.

  If the entered drive does not contain a disk, an error message
  appears. Press any key, insert the correct disk in the specified
  drive, then press [Enter].

  If the entered drive or path does not exist, an error message
  appears. Press any key, correct the entered drive or path name,
  then press [Enter].
 
3. Type the desired file name, then press [Enter]. If the same file
   name exists under the specified path, a warning message appears.
   If the same file names does not exist under the specified path, the
   "Save file name" window opens.
   
   If you prefer, press [F9] to open the "Directory" window.  Select
   the desired file name, then press [Enter] twice.

4. Select "[OK]" or "[Cancel]" then press [Enter], or simply press
   [O] or [C].

< Delete >

The Delete function allows you to delete unnecessary files from the
desired disk thereby freeing up disk space.

1. Selecting "Delete" then press [Enter], or simply press [D]. The
   "Drive & Path" window opens and shows the currently selected drive
   and path name.
2. Type the desired drive and path name, then press [Enter].  The
   "Directory" window opens.

   If the entered drive does not contain a disk, an error message
   appears. Press any key, insert the correct disk in the specified
   drive, then press [Enter].

   If the entered drive or path does not exist, an error message
   appears. Press any key, correct the drive or path name, then press
   [Enter].

   If no file exists under the drive and path names, an error message
   appears. Press any key, correct the drive and path names, then
   press [Enter].

3. Select a file name using the up- or down-arrow key, then press
   [Enter]. The "Delete file name" window opens.
4. Select "[Ok]" or "[Cancel]" then press [Enter], or simply press 
   [O] or [C].  After erasing the last file in the current directory,
   the Channel Information window opens; otherwise the "Directory"
   window opens again.
5. Repeat step 3 and 4 to delete all unnecessary files.

< Print(=F5) >

The Print function directs data to the printer.  The data may have
been created, loaded from a disk, or read from the transceiver. The
information that you can print includes the followings:

* File name
* Model name
* Optional features
* Key assignment
* Scan information
* DTMF
* 5-Tone
* 2-Tone
* Test Frequency
* Embedded message
* Group information

1. Select "Print(=F5)" then press [Enter], or simply press [P]. The
   "Print out list" window opens.
2. Press the up- or down-arrow key highlight the setting to be
   changed.
3. Press [SPACE BAR] or [F2] to select "[Yes]" for printing or "No"
   for canceling the print operation.
4. At the bottom of print out list window, type the desired start
   group, then press [Enter]. Type the desired end group, then press
   [Enter].
5. Press [F5] to open the "Edit data print out" window.
6. Select "[Ok]" or "[Cancel]".  If the printer is not ready, an error
   message will appears.  Check the printer, then select
   "[Ok]" or "[Cancel]".


< Go to dos >

The "Go to dos" function allows you to temporarily exit the program
and go back to the DOS prompt.

1. Select "Go to dos" then press [Enter], or simply press [G]. The
   "Type EXIT to return to FPU" message and the DOS prompt appear.
2. To restore the previous screen, type "exit" then press [Enter].

Note:  The KPG-67D software can support this command only when your
       computer has sufficient memory.

< eXit (=F3) >

The exit function quits the program completely and restores the DOS
prompt.

1. Select "eXit (=F3)" then press [Enter], or simply press [X]. The
   "Return to DOS!" window opens.
2. Select "[Ok]" or "[Cancel]" then press [Enter], or simply press
   [O] or [C].


**[MODEL]**

The Model menu is used to specify the model of the transceiver to be
programmed.

**[EDIT]** 

When you select the desired menu item under "Edit", the corresponding
window opens and allows you to change the settings for each function.
Press [SPACE BAR], [Shift]+ [SPACE BAR], [F2], or [Shift]+ [F2] to
change the settings.  For functions such as Group Text Size (Optional
features), you also can directly enter numeric values via the keyboard.
Pressing [Alt] completes settings and restores the Edit menu; pressing
[Esc] completes settings and restores the Channel Information window.

< Optional features >

Allows configuration of optional features on the transceiver.

1. When "Optional features" is selected, the "Optional Features"
   window opens.
2. Select the desired item.  For details on the selected item, press
   [F1] to access the Help window.
3. Change the setting.
4. Press [Alt] or [Esc] to complete the setting.

< Key assignment >

Key assignment programs the keys or controls on the transceiver.

1. When "Key assignment" is selected, the "Key Assignment" window
   opens.
2. Select the desired key. Press [F2] to access the Key List window.
   For details on the selected item, press [F1] to access the Help
   window on the Key List window.
3. Change the setting.
4. Press [Alt] or [Esc] to complete the setting.

< Scan information >

Allows configuration of functions relating to scan.

1. When "Scan information" is selected, the "Scan Information" window
   opens.
2. Select the desired function.
3. Change the setting.
4. Press [Alt] or [Esc] to complete the setting.

< Dtmf >

Dtmf allows you to configure the DTMF functions.

1. When "Dtmf" is selected, the "DTMF" window opens.
2. Select the desired parameter.
3. Change the setting.
4. Press [Alt] or [Esc] to complete the setting.

< 5-tone >
5-tone allows you to configure the 5-Tone functions.

1. When "5-tone" is selected, the "5-TONE" window opens.
2. Select the desired parameter.
3. Change the setting.
4. Press [Alt] or [Esc] to complete the setting.

< 2-tone >

2-tone allows you to configure the 2-Tone functions.

1. When "2-tone" is selected, the "2-TONE" window opens.
2. Select the desired parameter.
3. Change the setting.
4. Press [Alt] or [Esc] to complete the setting.

< Test frequency >

In the Test Mode and Tuning Mode, the transceiver receives and
transmits on Test frequencies.

1. When "Test frequency" is selected, the "Test Frequency" window
   opens.
2. Select the desired frequency number.
3. Enter the RX/TX Frequency.
4. Press [Alt] or [Esc] to complete the setting.

< Embedded message >
 
This function allows you to type up to a 64 alphanumeric character
message into the transceiver. This can be used for an electric serial
number, program file name notation, property ID., etc.. The entered
message is visible while running the KPG-67D software and prints out
on paper.

1. When "Embedded message" is selected, the "Embedded Message" window
   opens.
2. Enter up to 32 alphanumeric characters, then press [Enter].  The
   cursor moves to the lower column.
3. Enter up to 32 alphanumeric characters.
4. Press [Alt] or [Esc].

**[PROGRAM]**

< Read from radio >

This function reads all program data from the transceiver's flash
memory.

1.  When "Read from radio" is selected, the "Read from radio" window
    opens.
2.  Select "[Ok]" or "[Cancel]".

Note 1:  If communication with the transceiver is not possible for any
         reason, the "Check Connection Error" window opens.  Confirm 
         that the transceiver is correctly connected to the computer
         via a KPG-22/46 cable, then select "[Retry]".

< Write to radio >

This function writes data into the transceiver's flash memory.

1. When "Write to radio" is selected, the "Write to radio" window
   opens.
2. Select "[Ok]" or "[Cancel]". "[Ok]" writes data into the
   transceiver. "[Cancel]" aborts the write function and re-displays
   the Program menu.

Note 1:  If communication with the transceiver is not possible for any 
         reason, the "Check Connection Error" window opens.  Confirm
         that the transceiver is correctly connected to the computer
         via a KPG-22/46 cable, then select "[Retry]".

< Test Mode >

This function allows you to test various aspects of the transceiver.

CAUTION:  ALWAYS CONNECT A 50 OHM DUMMY LOAD PRIOR TO TRANSMITTING.
          BEFORE ENTERING THE TEST MODE, YOU MUST EXECUTE READ FROM
          RADIO OR WRITE TO RADIO.

1. When "Test mode" is selected, the "Test Mode Channel & Signalling"
   window opens.
2. Select the desired channel number then press [Enter].
3. Enter an appropriate signalling number 1 to 12.
4. Move the cursor to "Wide/Narrow" using the right- or left-arrow 
   key, and switch "Wide" and "Narrow" using the up- or down-arrow
   key, then press [Enter].
5. Press [SPACE BAR] or [F2] to toggle between transmit and receive.
6. Press [Alt] or [Esc]. 

Note 1:  If communication with the transceiver is not possible for 
         any reason, the "Check Connection Error" window opens.
         Confirm that the transceiver is correctly connected to the
         computer via a KPG-22/46 cable, then select "[Retry]".

< Tuning Mode >

To access "Tuning mode" under "Test mode", use the following steps:

1. While the "Test Mode Channel & Signalling" window is visible,
   select the desired settings.
2. Press [F10] to open the "Tuning Mode" window.
3. Select the desired item, then press [Enter].  The corresponding
   window opens.  For the descriptions of this window, access the
   window and use the [F1] key.


< firmware Program >

This function writes the firmware to the transceiver.
When you select this function, Firmware Programming Software(FPRO.EXE)
is activated.
When you activate the Firmware Programming, the startup screen
appears first. Press any key to progress to the Firmware Programming
Main screen.
In the Main screen, select the baud rate (bps) and the Firmware File
(HEX File). Press [F10], the software starts writing the main program
into the transceiver flash memory.
Use this function for upgrading the transceiver.
(See the service Manual for details)

Note 1:  If the computer does not have sufficient memory, exit KPG-67D
         and execute FPRO.EXE only.

Note 2:  When programming the firmware, it is recommended to copy the
         data from the floppy disk to your hard disk, before updating
         the radio firmware. Directly copying from the floppy disk to
         the radio may not work because the access speed is slow.

**[SETUP]** 

< Communication port >

Select either COM1 or COM2 as the port for communicating with the
transceiver.  If the computer has only one communication port, the
port is automatically set to COM1.

1. When "Communication port" is selected, the "Communication Port"
   window opens.

   If there is only a COM1 port on your computer, a window opens to
   report this fact.  In this case, the communication port cannot be
   changed.

2. Select either "[COM1]" or "[COM2]".
3. Press [Esc] to complete the setting and restore the Channel
   Information window.

< Display color >

Display color allows you to select the Color mode or Black & White
mode. Color mode permits changing colors of the Menu bar, windows,
messages, etc.
Select either mode depending on the computer display.

1. When "Display color" is selected, the "Display Color Mode" window
   opens.
2. Select either "[Color]" or "[Black & White]".

   If "[Color]" is selected, the "Setup Display Color" window opens
   and you can proceed to the following steps:

3. Select the item that you wish to configure.
4. Select the desired color.  If you want to reset all colors to
   their initial settings, press [F10].
5. Repeat steps 3 and 4 to select colors for the remaining items.
6. Press [Esc] to complete the setting and restore the Channel
   Information window.

< Help path >

Use Help path to select the drive and path name of the Help files.
The Help files are called KPG67D_*.HLP and are automatically loaded
in the same folder as the program file upon using the install command
for installation.

1. When "Help path" is selected, the "Drive & Path" window opens.
2. Type the drive and path name, then press [Enter].  The window
   closes and the Channel Information window opens.

If the entered drive does not contain a disk, an error message
appears. Press any key, insert the correct disk in the specified
drive, then press [Enter].

If the entered drive or path does not exist, an error message appears.
Press any key, correct the entered drive or path name, then press
[Enter].

If the Help file is not found under the selected drive and path name,
an error message appears.  Press any key, correct the drive and path
names, then press [Enter].

Note:  The Help file can be moved to the directory of your choice.

< Fpro path >

Use "Fpro path" to select the drive and path name of the
Firmware program named "FPRO.EXE".  If an incorrect drive or
path name is entered, the program will not correctly initiate.

1.  When "Fpro path" is selected, the "Drive & Path" window opens.
2.  Type the drive and path name, then press [Enter]. The window
    closes and the Channel Information window opens.

Note 1:  If the entered drive does not contain a disk, an error
         message appears.  Press any key, insert the correct disk in
         the specified drive, then press [Enter].

Note 2:  If the entered drive or path does not exist, an error message
         appears.  Press any key, correct the entered drive or path
         name, then press [Enter].

Note 3:  If the "FPRO.EXE" program is not found under the selected
         drive and path name, an error message appears.  Press any
         key, correct the drive and path names, then press [Enter].

**[F1=HELP]** 

< Help Hot Key [F1] >

For an explanation of the item at which the cursor is currently
positioned, press [F1].  The corresponding window opens and explains
the details.
Pressing [F1] again opens a window that lists the menu items of the
current menu title.  Pressing [F1] one more time opens a window that
lists the menu titles.

The keys available while accessing help windows are listed at the
bottom of the screen (Key summary section).  To close the window,
press [Alt] or [Esc].

< General help >

Now you are using the General help function that explains how to
operate the KPG-67D software.

< Keyboard help >

Keyboard help explains the functions of the keyboard keys.

Keyboard Help
    *** [ Computer Keyboard Help ] ***
This help describes the functions of the keyboard keys.

[Esc]: Restores the Channel Information window.

[Alt]: Opens and closes the menu, or restores the previous screen.

[Tab]: While in Test Mode, switches the frequency when 3-Point or
       5-Point adjustment item is activated.

[Home]: Jumps to the first channel of the Channel Information window
        or the first page of a help window.

[PgUp] & [PgDn]: Scrolls the General Help window, Keyboard Help
                 window, a Channel Information window, or a file
                 directory window one page at a time.

[End]: Jumps to the last channel of the Channel Information window or
       the last page of a help window.

[Enter]: Sets the entered data.

Arrow keys: Moves the cursor to the desired item, or scrolls help
            windows.

[SPACE BAR]: Changes the setting at the current cursor position.
             TX,RX toggle while in Test and Tuning mode.

[Shift]+[SPACE BAR]: Changes the setting in the opposite direction at
                     the current cursor position.

[Ctrl]+[R]: Opens the "Read from radio" window.

[Ctrl]+[W]: Opens the "Write to radio" window.

[F1]: Opens a help window for the item at the current cursor position.

[F2]: Changes the setting at the current cursor position.
      TX,RX toggle while in Test and Tuning mode.
      In the Key assignment window, press to open a list of key
      functions.
      In a Channel Information or Channel Edit window, with Encode or 
      Decode highlighted, press to open a list of available QT/DQT
      settings.

[F3]: Exits the program and restores the DOS prompt.

[F4]: Saves the currently displayed programming data with the current
      file name.

[F5]: Prints out the currently displayed programming data, tuning
      data, or help window.

[F7]: In the Channel Information, Channel Edit window, Group number
      increment.

[F8]: In the Channel Information, Channel Edit window, Group number
      decrement.

[F9]: In the "save As/Save file name" window, press to open the
      "Directory" window.

[F10]: In the Channel Information, opens the "Channel Edit" window.
       Resets the display color settings (Setup menu) to the defaults.
       When in Test mode, opens the "Tuning Mode" window.

[Shift]+[F2]: Changes the setting in the opposite direction at the
              current cursor position.

[Shift]+[F3]: In the Channel Information, Channel Copy window opens.

[Shift]+[F4]: In the Channel Information, Frequency Copy window opens.

[Shift]+[F5]: In the Channel Information, QT/DQT Copy window opens.

[Shift]+[F8]: In the Channel Information, Group Copy window opens.

[Shift]+[F9]: In the Channel Information, insert the channel data
              space at the current cursor position.

[Shift]+[F10]: In the Channel Information or Channel Edit window, all
               of the channel data at the current cursor position are
               deleted.

End Of Help File
